MacBook Won’t Turn On
A MacBook that won’t turn on often has a drained battery or a power problem rather than a hardware failure. Plug the Apple power adapter into a working wall outlet and let it charge for about 20 minutes. Then press and hold the power button (or Touch ID) for about 10 seconds, release it, and press it again.
Try these quick fixes first
- Plug the Apple power adapter into a wall outlet you know works, with the cable firmly seated at both ends.
- Let it charge for about 20 minutes.
- Hold the power button (or Touch ID) for about 10 seconds, release it, then press it once.
- Unplug every accessory, including docks, hubs and drives.
- Press the Increase Brightness key a few times in case the screen is just dimmed all the way.
Check the power adapter, cable and outlet
A MacBook with a flat battery can’t start until enough power reaches it, and a damaged cable, a dead outlet or a low-wattage charger can stop that.
- Check the cable for damage and plug it in firmly at both ends.
- Test the outlet with a lamp or another device you know works.
- Use the Apple adapter and cable that came with the MacBook, or another Apple one that fits. Some USB-C cables carry only data, and a lower-wattage adapter may not supply enough power.
- Unplug the adapter from the wall for 60 seconds, then plug it back in. Apple says an adapter can shut itself off when it senses electrical noise on the circuit, and this resets it.
- Check the charging port for debris. Apple suggests a dry cloth for a MagSafe port and compressed air for a USB-C port.
Let the battery charge first
A completely flat battery may need a while on the charger before the power button does anything.
- Leave the MacBook on the Apple adapter for about 20 minutes. Apple says a Mac in a low-battery state may need that long before you can use it.
- On a MacBook with MagSafe, the light on the connector glows amber while it charges.
- If that light keeps flashing amber, Apple says it may point to a charging problem. Unplug the cable at both ends, wipe the MagSafe port and connector with a dry cloth, and reconnect.
- Then press the power button.
Hold the power button for 10 seconds
A MacBook that stopped responding while asleep can look dead, and holding the power button forces it off so it can start fresh.
- Keep it plugged in. Press and hold the power button for about 10 seconds. On models with Touch ID, press the Touch ID button down firmly rather than just touching it.
- Release it, then press and release the power button normally.
- If nothing happens, unplug all accessories, including printers, drives, USB hubs, docks and phones, and repeat.
Is it on, but the screen is dark?
A MacBook can run with a black screen, so check for signs of life before you decide it’s dead.
- Listen for a startup sound and look for the keyboard backlight. Not every Mac plays the sound, and it can be turned off, so silence proves nothing.
- Press and hold Caps Lock for a moment. If its light comes on, the MacBook has power. Apple builds in a short delay, so a quick tap may not light it.
- Press the Increase Brightness key several times. Apple notes that brightness can be turned all the way off.
- If the screen stays black, hold the power button for up to 10 seconds until the MacBook turns off, then turn it on again.
- An Apple logo, question mark or circle with a line through it that won’t go away means the MacBook is on but can’t finish starting up. A macOS update can keep the logo and progress bar up much longer than usual, so give it time. Otherwise, turn it off and on once with the power button. If the screen returns, call IT, because the next fixes use macOS Recovery.
Test it with an external display
If the MacBook shows signs of life but its screen stays black, a monitor shows whether the computer works and just the built-in display has failed.
- Use a monitor this MacBook has used before. On Apple silicon models, a new display can wait for your approval on screen and stay dark until you allow it.
- Connect it directly to a Thunderbolt (USB-C) or HDMI port, not a hub or dock, and keep the lid open.
- If your login window or desktop appears on the monitor, the MacBook works and its built-in display needs repair. Call IT, and use the monitor until then.
- If the monitor stays dark too, try the SMC step below if it applies, then call IT.
Reset the SMC (Intel MacBooks only)
On Intel-based Macs, the System Management Controller (SMC) manages power and charging, and resetting it can clear a fault that keeps the MacBook from starting.
- Find your type. MacBook Neo, and MacBook Air or Pro models with an M1 chip or later (late 2020 onward), use Apple silicon. Intel MacBook Air and Pro models from 2018 to 2020 have the Apple T2 Security Chip. Not sure? Ask IT.
- Apple silicon: there’s nothing to reset. Apple says the SMC resets itself when the Mac shuts down and starts again on power, so keep it plugged in and repeat the power button steps.
- Intel with the T2 chip: hold the power button for 10 seconds, release it, wait a few seconds, then turn it on. If it still won’t start, hold the left Control, left Option and right Shift keys for 7 seconds, then add the power button and hold all four for 7 more seconds. Release them, wait a few seconds, and press the power button.
- Older Intel models: hold the left Shift, Control and Option keys, then press and hold the power button too. Hold all four for 10 seconds, release them, then press the power button.
Spilled something, dropped it, or is the case bulging?
Liquid, a fall or a swollen battery can damage parts inside, and powering on a damaged MacBook can make it worse or injure you.
- After a spill, unplug the adapter and every cable, and shut the MacBook down right away, holding the power button if you have to, even if that loses unsaved work.
- Don’t charge it or turn it on while it might be wet. Don’t use heat or compressed air to dry it, don’t push anything into the ports, and don’t put it in rice. Call IT.
- If the case bulges, the trackpad sits higher than usual, or the MacBook rocks on a flat desk, the battery may be swollen. Stop using and charging it, don’t press on it, and call IT. Apple warns that a damaged battery can overheat or cause a fire.
- If it was dropped and now won’t turn on, unplug it and call IT. Don’t use a MacBook with a cracked screen or damaged case. Apple warns that it can cause injury.
Why does this happen?
- A fully drained battery, or a MacBook left unused for a long time.
- A damaged or data-only cable, a low-wattage adapter, a dead outlet, or electrical noise that made the adapter shut itself off.
- An accessory, hub or dock that interferes with startup.
- The MacBook is on, but the brightness is all the way down, the display has failed, or macOS can’t finish starting up.
- An SMC fault on Intel models.
- Liquid, a fall, or a worn-out or swollen battery.
When should you call IT?
- It still won’t turn on after charging, holding the power button and, on Intel models, an SMC reset.
- It shows signs of life but the screen stays black, or it stops at a logo or symbol. Those fixes use macOS Recovery.
- Liquid got in, it was dropped, or the case is bulging.
- The adapter is damaged or discolored, or sparks from anywhere other than the plug’s blades.
If the MacBook holds files that aren’t backed up anywhere else, read about our data recovery service before it goes in for repair.
OAC Technology’s IT support team fixes problems like this for businesses across the Twin Cities. Clients can call 952-548-5558, Monday to Friday, 8 a.m. to 6 p.m. Central. Not a client yet? Call the same number or send us a message.
Common questions
Why is my MacBook not turning on?
Usually because the battery is fully drained or not enough power is reaching it. Charge it with the Apple adapter for about 20 minutes, then hold the power button for about 10 seconds and press it again. If it still won’t start, it may need repair.
How do you force start a dead MacBook?
Plug in the Apple adapter, then press and hold the power button (or Touch ID) for about 10 seconds. Release it and press it once. On an Intel MacBook, an SMC reset can also help.
How long does it take for a MacBook to turn on after it dies?
Give it about 20 minutes on the charger. Apple says a Mac in a low-battery state may need that long before you can use it.
Why is my MacBook Air not turning on when plugged in?
The adapter, cable or outlet may not be delivering enough power. Use the Apple adapter and a charging cable, test the outlet with a lamp, and unplug the adapter from the wall for 60 seconds.
What is the Mac black screen of death?
It’s an informal name for a Mac that seems to turn on but shows only a black screen. Press the Increase Brightness key, then hold the power button for up to 10 seconds and start it again. If it stays black, call IT.
Why is my MacBook Pro or MacBook Air not turning on?
Usually a drained battery or too little power, and the fixes are the same for both: charge it with the Apple adapter from a wall outlet for about 20 minutes, unplug accessories, then hold the power button (or Touch ID) for about 10 seconds and press it again. Only Intel-based models can also need an SMC reset; MacBook Air and MacBook Pro models with an M1 chip or later reset it on their own.









